|
Parts for sale Tonti |
Post Reply 
|
| Author | |
Ken-Guzzibear 
Moderator Group 
Joined: 13 May 2014 Location: Sileby Leics Status: Offline Points: 9457 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Parts for sale TontiPosted: 13 Aug 2024 at 16:53 |
|
Been looking in my shed and a tidy up I have not yet checked these for size but 3 Cylinders I think V1000 round might be 850 but will measure tomorrow.
A Bevel box A shaft drive for big block and one I think must be from a small block There are 2 Front timing covers from a Convert I have a Crankcase as well with timing chain & gears and complete crank with rods If any one is interested I am happy to take pics I will be popping them on flea bay in Sept. Make me decent offers they are not scrap. I have a fair few other bits I will just pop on line Stuff like a Bosch Voltage reg and a fuse box for spade fuses only did a clean up today too hot to get pics done etc put this here first I am near Loughborough Leics Cheers Ken
|
|
|
The Older i Get, The Better I Was
|
|
 |
|
|
AdrianW
Senior Member 
Joined: 05 May 2019 Location: Bristol Status: Offline Points: 1208 |
Post Options
Thanks(0)
Quote Reply
Posted: 14 Aug 2024 at 09:21 |
|
Ken, I have found on my V50III project that turning the rear wheel makes a louder "clank" than my V35II, sound appears to be coming from the UJ area. If the smaller shaft is from a small block and has 12 splines & doesn't have play I could be interested.. Cheers, Adrian Bristol UK
|
|
|
|
|
Ken-Guzzibear
Moderator Group
Joined: 13 May 2014 Location: Sileby Leics Status: Offline Points: 9457 |
Post Options
Thanks(0)
Quote Reply
Posted: 14 Aug 2024 at 11:41 |
|
I know nothing about small block bikes but I will be getting pictures of the bits you would have to figure out if it's ok. At the moment got a few other things to do this here retirement is so busy lol
|
|
|
The Older i Get, The Better I Was
|
|
|
|
|
AdrianW
Senior Member
Joined: 05 May 2019 Location: Bristol Status: Offline Points: 1208 |
Post Options
Thanks(0)
Quote Reply
Posted: 14 Aug 2024 at 12:25 |
|
Thanks Ken... Cheers, Adrian Bristol UK
|
|
|
|
|
Ken-Guzzibear
Moderator Group
Joined: 13 May 2014 Location: Sileby Leics Status: Offline Points: 9457 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Aug 2024 at 13:11 |
|
Had a look it's more than 12 spline so not what you want
|
|
|
The Older i Get, The Better I Was
|
|
|
|
|
AdrianW
Senior Member
Joined: 05 May 2019 Location: Bristol Status: Offline Points: 1208 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Aug 2024 at 13:34 |
|
thanks Ken.... Cheers, Adrian Bristol UK
|
|
|
|
|
PHIL H
Senior Member
Joined: 18 Jan 2016 Location: SW Yorkshire Status: Offline Points: 149 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 Aug 2024 at 12:04 |
|
Hi Ken, I've been building a SP3 custom. It's been a real challenge and after 200 miles on it discovered the crank is scrap !
Do you still have the crankcase, timing gears and crank for sale and if so what are they off ? Thanks Phil |
|
|
1993 SP3
Triumph Tiger GT PRO 1976 Honda CB 550 project |
|
|
|
|
russellp
Falcone 
Joined: 24 Nov 2021 Location: Peterborough Status: Offline Points: 41 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Aug 2024 at 16:27 |
|
Hello Phil,
If Ken is unable to help you I have a bottom end (crank, rods, bearings) and timing gears engine number VG 204xxx which I believe is from an SP or G5. Let me know if you’re interested. Russell
|
|
|
|
|
PHIL H
Senior Member
Joined: 18 Jan 2016 Location: SW Yorkshire Status: Offline Points: 149 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Aug 2024 at 21:57 |
|
Thanks Russell but I picked an engine up from Gutsibits yesterday. It's obviously been sat for years so always good to have a back up.
Many thanks Phil |
|
|
1993 SP3
Triumph Tiger GT PRO 1976 Honda CB 550 project |
|
|
|
|
russellp
Falcone
Joined: 24 Nov 2021 Location: Peterborough Status: Offline Points: 41 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2024 at 16:19 |
|
Hello Phil,
Pleased you’re sorted. If you don’t mind me asking, how much did you pay for the engine? I ask because I have a rebuilt LM2 engine and clutch which I intend to sell and I would like to have a feeling for its value. Regards, Russell
|
|
|
|
|
Ken-Guzzibear
Moderator Group
Joined: 13 May 2014 Location: Sileby Leics Status: Offline Points: 9457 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 Sep 2024 at 15:57 |
|
Just put loads of items on E-Bay including a pair of VHB30 Dellorto carbs
|
|
|
The Older i Get, The Better I Was
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options