Tape residue left on paintwork.. |
Post Reply | Page <12 |
Author | |
italianmotor
Senior Member Joined: 14 May 2014 Location: UK Status: Offline Points: 2101 |
Post Options
Thanks(0)
|
I'm going to flat it back first and see how it looks. I really won't be starting again..
|
|
Jerry atric
Senior Member Joined: 24 Nov 2014 Location: Wiltshire Status: Offline Points: 3367 |
Post Options
Thanks(0)
|
Haha. You have my complete sympathy. Of course, as long as the paint has gone off well, flatting it will solve the problem. The start again remark was meant if it wasn't hard. Good luck.🙂
|
|
-HJB-
Senior Member Joined: 19 Apr 2015 Location: Warwickshire Status: Offline Points: 435 |
Post Options
Thanks(0)
|
+1 with careful flatting back with very fine wet and dry followed by a few good coats of lacquer.
|
|
Mike H
Senior Member Joined: 21 May 2014 Location: East Anglia Status: Offline Points: 8733 |
Post Options
Thanks(0)
|
Just painted a new Bantam mainstand, needed touching up a bit afterwards as always where I missed bits, foolishly I did that with it lying on paper (it was hanging up on wire before) of course bits of paper have tore off and got stuck to it, now waiting for it to harden some more before I have to rub it down and spray over again, not as critical as a tank admittedly but self ass kicking nonetheless so I sympathise!
|
|
"Chicken nuggets don't dance on a Tuesday."
|
|
Brian UK
Moderator Group Joined: 13 May 2014 Location: Surrey Status: Offline Points: 17641 |
Post Options
Thanks(0)
|
I've had more than my fair share of hiccups when painting.
|
|
Brian.
Better 5 minutes late in this world than years early in the next. |
|
italianmotor
Senior Member Joined: 14 May 2014 Location: UK Status: Offline Points: 2101 |
Post Options
Thanks(0)
|
I've left this tank now for at least week after applying the black stripes, 2 coats, and look what's happened? I had the tank hanging up for a few says, then had it sat on some cloth, and it's taken on the marks of the cloth. I know I'm no professional sprayer but this is ridiculous. I think this paint isn't fit for purpose?
I'll just flat it back and hope for the best. I assume not good to polish with anything before lacquer goes on?
|
|
iansoady
Senior Member Joined: 23 Jul 2017 Location: Redditch Status: Online Points: 2402 |
Post Options
Thanks(0)
|
I hate to say it but it sounds as though the paint just isn't suring properly. The only real solution is probably to strip it all off and start again. I've had some real nightmares with incompatible paints and they only usually show up in the last stages. The last disaster was using halfords "petrol proof" lacquer over one-shot lining paint. Of course it all bubbled up. I later discovered after testing that the one-shot stood up OK to the odd splash of petrol.......
|
|
Ian
1952 Norton ES2 1986 Honda XBR500 1958-ish Greeves/Triumph in progress |
|
c13pep
Senior Member Joined: 31 Aug 2017 Location: Doncaster Status: Offline Points: 2110 |
Post Options
Thanks(0)
|
As a last resort you could try `baking` the paint in front of an infra red heater on a very low setting, but I fear the original paint has reacted and thus may never properly harden.
Have to agree with Ian about starting again especially as it`s the petrol tank Lacquering on top of that may just be a waste of time CHRIS
|
|
you can`t have any fun in a straight line
Monza Honda CB77 project |
|
italianmotor
Senior Member Joined: 14 May 2014 Location: UK Status: Offline Points: 2101 |
Post Options
Thanks(0)
|
I'm going to complain anyway, I've followed all their instructions and all their products, sprayed always in dry wetaher and I haven't done excessive coats, so will try to get some money back.
|
|
italianmotor
Senior Member Joined: 14 May 2014 Location: UK Status: Offline Points: 2101 |
Post Options
Thanks(0)
|
I might try that. Not sure what you mean by paint reacting?
|
|
Ken-Guzzibear
Moderator Group Joined: 13 May 2014 Location: Sileby Leics Status: Offline Points: 9454 |
Post Options
Thanks(0)
|
Other than small parts i have stopped attempting to paint, when off earlier this year got a mudguard to bare metal, cleaned it off, proper primer, rubbed it down when the top coat went on ...it went crazed, never had it before so did not paint tank or side panels rubbed them right down, took mudguard back to bare metal, took it to Richard Bexon, I bought black acrylic paint from an e-bay supplier known to Richard, he then primed and painted the parts for a reasonable price. Yes I paid for the paint £45 .... BUT when rattle cans are £10 a pop and for some reason it often goes crazed or you get the micro bubbles or just dust it is not worth it. The paint in cans i got to do the mudguard, that did not work cost £35 .... plus time ... nope not worth it.
|
|
The Older i Get, The Better I Was
|
|
c13pep
Senior Member Joined: 31 Aug 2017 Location: Doncaster Status: Offline Points: 2110 |
Post Options
Thanks(0)
|
Paint will react to many things but usually not getting base absolutely clean is the main one.
My son always starts with etching primer on any second-hand part I give him just to try and minimise any chance of a reaction with the base. On a recent Aprilia project we had seven attempts at getting a rear seat panel to accept the initial coating and we still didn`t know what was causing the problem when we finished. It was most likely something embedded in the plastic, but who knows and that was Halfords rattle cans which he tells me are very good CHRIS |
|
you can`t have any fun in a straight line
Monza Honda CB77 project |
|
italianmotor
Senior Member Joined: 14 May 2014 Location: UK Status: Offline Points: 2101 |
Post Options
Thanks(0)
|
The paint hasn't reacted, it just has not dried as it should. My preparation was fine and thorough, and I also used etch primer.
|
|
italianmotor
Senior Member Joined: 14 May 2014 Location: UK Status: Offline Points: 2101 |
Post Options
Thanks(0)
|
Yes but I was being quoted 500-750 pounds locally to spray tank, mudguard, 2 side panels, seemed excessive to me.
|
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |