cylinder compression test v1000 |
Post Reply | Page <12 |
Author | |
v7john
Senior Member Joined: 14 May 2014 Location: West Wales, UK. Status: Offline Points: 703 |
Post Options
Thanks(1)
|
Years ago I was told a way to get a rough idea of what the reading should be when you do a compression test. This is what I put in my blog when checking my V7 700 loop.
"As I’ve got a compression tester I thought I might as well use it! It’s a cheap one I bought many years ago when I was into classic cars. It takes both hands to hold it against the spark plug hole while the Mrs holds the throttle wide open and pushes the starter. I got a reading of 132psi on the left and 140psi on the right. These are close enough to each other to be acceptable and are high enough. Both figures are reached in 4 revs. Apparently you can work out roughly what the reading should be in psi from the engines’ compression ratio. As the V7 compression ratio is 1:9 then the reading should be 9 x 14.7, which is the atmospheric pressure at sea level, plus an amount for an increase caused by the heat generated by the compression process. That comes out at 132 plus a bit. Pretty good then I reckon". If you think the compressions are down I would put a bit of oil in the spark plug hole and repeat the process. If that gives a significant improvement the problem could be the rings. If not then I'd check the valves. One other thing. Make sure the valve clearances are correct before doing the test. |
|
1972 V7Sport "The Racing Rhino".
1972 V7 700cc "The Fire Bike". 1954? Superalce 1954 BSA M33 (to be sold) Read my blog https://racingrhino.wordpress.com/ |
|
v1000-tog
Senior Member Joined: 08 Apr 2016 Location: East Yorkshire Status: Offline Points: 120 |
Post Options
Thanks(0)
|
the G5 has a compression ratio of 9.1:1 so 134 PSI using your calculation.
so at 125 psi it has lost 9 psi in nearly 40 years. I will put a bit of oil in and test again posting the result. see if it gets the lost 7% back. - thanks
|
|
red leader one
Senior Member Joined: 07 Oct 2014 Location: Cullercoats Status: Offline Points: 4466 |
Post Options
Thanks(0)
|
That's the Angels share.
|
|
PHIL H
Senior Member Joined: 18 Jan 2016 Location: SW Yorkshire Status: Offline Points: 140 |
Post Options
Thanks(0)
|
I got similar on my G5 about 125 to 130
On my SP I got 85 on left and 125 on right...time to open tool box I think! |
|
1993 SP3 Kawasaki Z650 1976 Honda CB 550 project |
|
Mike H
Senior Member Joined: 21 May 2014 Location: East Anglia Status: Offline Points: 8733 |
Post Options
Thanks(0)
|
|
|
"Chicken nuggets don't dance on a Tuesday."
|
|
Phil
Falcone Joined: 20 Jan 2016 Location: Yorkshire Status: Offline Points: 29 |
Post Options
Thanks(0)
|
Erhmm not quite you are mixing pressure units atmospheric pressure (a) and gauge pressure (g). atmospheric pressure of 1 bar a is 0 bar g. 9 times atmospheric pressure 9 bar a is 8 bar g ( 116 psi g )
A compression test is more complicated than boyles law accounts for as it takes no account of cam timing, heat caused by compression and any fuel in the gas charge. Edited by Phil - 09 Nov 2017 at 21:58 |
|
Jools
Senior Member Joined: 19 Aug 2016 Location: Milton Keynes Status: Offline Points: 273 |
Post Options
Thanks(0)
|
And again, ah, er ..... no.
'Gauge pressure' is the only referenced measurement here. The type of pressure gauge used by 99.9% of us are calibrated to read '0.0' under STP, i.e. standard temperature and pressure of 20 degrees C and 1 Atmosphere/14.696psi/101.325kPa (the last being the SI unit of pressure). The instrument will then read in terms of 'Gauge Pressure'. In addition, the type of gas used in the calibration process will be the same as that which the gauge is expected to measure in use (air/nitrogen/acetylene/etc). Only in those instances where the pressure gauge has been calibrated to read '0.0' against a total vacuum, will the instrument read in terms of 'Absolute Pressure', e.g. like a meteorlogical Barometer. Thus, as we are dealing solely with the former type of calibration, there is no need to apply any correction. Strictly speaking, any deviation from STP will make a difference. Cam timing will also make a difference if either valve is open when the piston begins to rise from BDC on the compression stroke, and any fuel mixture drawn in will similarly affect the gauge reading as its compressibility will be different from the gauges' calibration gas (air in the majority of cases). All in all, the 'rough guide' figures are quite adequate for our purposes.
|
|
Jools
V1000G5 1972 T150V 1961 Royal Enfield Constellation 1971 Suzuki ACC50 erm... 1963 Philips Panda (and other assorted detritus) |
|
Phil
Falcone Joined: 20 Jan 2016 Location: Yorkshire Status: Offline Points: 29 |
Post Options
Thanks(0)
|
No... you are missing the point ... you cannot say 9 x atmospheric pressure should give you 9 bar gauge.
|
|
v7john
Senior Member Joined: 14 May 2014 Location: West Wales, UK. Status: Offline Points: 703 |
Post Options
Thanks(0)
|
You’re probably right Phil. As you say, the gauge reads zero when atmospheric pressure is already at about 1 bar. 1 bar = 14.5 psi, 1 atmosphere = 14.7psi. They aren't quite the same.
Remember, I did say it was a "way to get a rough idea of what the reading should be" in the first sentence of my original post on this. It's only an estimate. Making a more accurate calculation gets much more involved and is well beyond me. In my notes I have a more complete method to find pressure at TDC but it’s still only a more accurate way of making an estimate; p(TDC) = p(BDC) x CR raised to the power of 1.3 for the heat ratio of an air/petrol mixture X 60% for the volumetric efficiency of a petrol engine, minus the 1 bar not registered by the gauge. So in my case that would give; P(TDC) = 1 x 9 ˄ 1.3 x 0.6 - 1 (in bar). P(TDC) = 1 x 17.40 x 0.6 - 1 = 10.44 -1 = 9.44 bar or 136.92 psi (using 9 x 14.7 gives 132.3 psi) For V1000-tog it would be; P(TDC) = 1 x 9.1 ˄ 1.3 x 0.6 -1 (in bar). P(TDC) = 1 x 17.65 x 0.6 -1 = 10.59 -1 = 9.59 bar or 139.1 psi (using 9.1 x 14.7 gives 133.77 psi) As you can see, the very basic method isn’t too bad if you’re just looking for a rough idea and I did say plus a bit “for an increase caused by the heat generated by the compression process”. You’re right about cam profiles being able to make a difference. The valves might not be closed for the whole of the piston stroke so reducing the pressure. There are a number of other factors as well such as the temperature of the cylinder etc. Quoted compression ratios are about a change in swept volume while the cylinder pressure increase relies on much more. |
|
1972 V7Sport "The Racing Rhino".
1972 V7 700cc "The Fire Bike". 1954? Superalce 1954 BSA M33 (to be sold) Read my blog https://racingrhino.wordpress.com/ |
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |